工頻交流焊機的調節周期較長，對50Hz的電網，焊接時間調節分辨率為20ms。逆變直流點焊機時間調節分辨率可達0.25ms(4kHz逆變頻率)，控制精度高。逆變焊機的反饋控制的響應速度明顯加快，輸出穩定性好。工頻交流焊機由于電流過零的影響，熱效率低，用晶閘管調節電流，當電流百分比偏小時，過零時間長，影響更大；逆變直流點焊機輸出電流為脈動直流，在回路電感的作用下為連續直流輸出，熱效率高，焊接熱輸入穩定。

    交流焊機與電容貯能點焊機比從焊接質量上來說：電容貯能焊機將電容中儲存的能量一次性釋放給焊接回路，輸出能量調節靠控制電容的充電能量完成，通常有調節充電電壓和電容容量兩種方法，輸出電流為脈沖電流，時間不能通過電子控制來調節。逆變直流焊機為較平穩的直流，電流通過逆變脈寬調節，時間通過逆變周期數調節，焊接能量可由電流和時間精確控制。

    從焊接速度上來說：電容貯能焊機需要合理的電容充電過程(否則電容易損壞)，降低了生產速度。逆變電阻點焊機沒有這一過程，焊接速度高。

    從節能效果上來說：電容貯能焊機的變壓器實際工作在更低的頻率，為防止飽和，變壓器鐵心更大，損耗加大；電容充電回路也增加損耗。逆變焊機變壓器工作在較高的頻率(1-4kHz)，損耗很小，直流輸出改善功率因素，節能效果明顯。

    從設備體積與重量：電容貯能焊機的變壓器鐵心大，儲能電容也占據相當的空間，設備笨重。逆變直流電阻點焊機變壓器小、沒有龐大的電容器組，設備較輕巧。